| Performance |
Forwarding bandwidth |
32 Gbps |
| Flash memory |
32 MB |
| Max VLANs |
1K |
| VLAN IDs |
4K |
| Switched Virtual Interfaces(SVIs) |
Up to 1000 |
| Maximum transmission unit(MTU) |
Up to 9000 bytes |
| Jumbo frames |
9016 bytes |
| MAC address |
Default Template:6K Access Template:4K VLAN Template:12K Routing Template:3K |
| IGMP groups and multicast routes |
Default Template:1K Access Template:1K VLAN Template:1K Routing Template:1K |
| Total unicast routes |
Default Template:8K Access Template:8K Routing Template:11K |
| Directly connected hosts |
Default Template:6K Access Template:4K Routing Template:3K |
| Indirect routes |
Default Template:2K Access Template:2K Template:8K |
| Security ACEs |
Default Template:1K Access Template:2K VLAN Template:1K Routing Template:1K |
| QoS ACEs |
Default Template:0.5K Access Template:0.5K VLAN Template:0.5K Routing Template:0.5K |
| PBR ACEs |
Access Template:0.5K Routing Template:0.5K |
| Connectors and Cabling |
10BASE-T ports: RJ-45 connectors, two-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling 10BASE-T PoE ports: RJ-45 connectors, two-pair Category 3, 4, or 5 UTP cabling power pins 1,2 (negative) and 3,6 (positive) 100BASE-TX ports: RJ-45 connectors, two-pair Category 5 UTP cabling 100BASE-TX PoE ports: RJ-45 connectors, two-pair Category 5 UTP cabling, power on pins 1,2 (negative) and 3,6 (positive) 1000BASE-T SFP-based ports: RJ-45 connectors, four-pair Category 5 UTP cabling 1000BASE-SX, -LX/LH, -ZX, and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber) Cisco Catalyst 3560 SFP Interconnect Cable: two-pair shielded cabling, 50 cm Management console port: RJ-45-to-DB-9 cable for PC connections; for terminal connections, use RJ-45-to-DB-25 female data-terminal-equipment (DTE) adaptor (can be ordered separately from Cisco; part number ACS-DSBUASYN=) |
| Power Connectors |
Customers can provide power to a switch by using either the internal power supply or the Cisco RPS 2300. The connectors are located at the back of the switch. Internal-Power-Supply Connector The internal power supply is an autoranging unit. The internal power supply supports input voltages between 100 and 240 VAC. Use the supplied AC power cord to connect the AC power connector to an AC power outlet. Cisco RPS Connector The connector offers connection for an optional Cisco RPS 2300 (model PWR-RPS2300) that uses AC input and supplies DC output to the switch. |
| Indicators |
Per-port status LEDs: Link integrity, disabled, activity, speed, full-duplex indications, PoE applied, PoE error, and PoE disabled indications System-status LEDs: System, RPS, link status, link duplex, link speed, and PoE indications |
| Dimensions (H x W x D) |
Inches:1.73 x 17.46x 11.62 Centimeters:4.4 x 44.3 x 29.5 |
| Weight |
Pounds:8.2 Kilograms:3.7 |
| Environmental Ranges |
Fahrenheit :32 to 113ºF Fahrenheit :0 to 45ºC |
| Acoustic Noise |
Sound Pressure :41 dB , 44 dB Sound Power :5.1 B, 5.4 B |
| Mean Time Between Failure (MTBF) |
377,260 hours |
| Power Supply Rated Maximum |
Switch Power Consumption :60W Total Output BTU : 205 BTU/hour |
| Measured 100% Throughput Power Consumption |
Switch Power Consumption :24W Total Output BTU :80 BTU/hour |
| Measured 5% Throughput Power Consumption |
Switch Power Consumption :22W Total Output BTU : 72 BTU/hour |
| AC/DC Input Voltage and Current |
Voltage (autoranging):100-240 VAC Current:0.5A – 0.3A Frequency : 50-60 Hz |
DC Output Voltages, Current, & Power consumption from RPS 2300 |
Switch :+12V at 2A Switch Power:24W |
| PoE |
Maximum power supplied per port: 15.4W Total power dedicated to PoE: 370W |
| Management |
BRIDGE-MIB CISCO-CDP-MIB CISCO-CLUSTER-MIB CISCO-CONFIG-MAN-MIB CISCO-ENTITY-FRU-CONTROL-MIB CISCO-FLASH-MIB CISCO-FTP-CLIENT-MIB CISCO-HSRP-MIB CISCO-HSRP-EXT-MIB CISCO-IGMP-FILTER-MIB CISCO-IMAGE-MIB CISCO-IP-STAT-MIB CISCO-L2L3-INTERFACE-CONFIG-MIB CISCO-MAC-NOTIFICATION-MIB CISCO-MEMORY-POOL-MIB CISCO-PAGP-MIB CISCO-PING-MIB CISCO-PROCESS-MIB CISCO-RTTMON-MIB CISCO-STP-EXTENSIONS-MIB CISCO-SYSLOG-MIB CISCO-TCP-MIB CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB CISCO-VLAN-MEMBERSHIP-MIB CISCO-VTP-MIB ENTITY-MIB ETHERLIKE-MIB IF-MIB IGMP-MIB IPMROUTE-MIB OLD-CISCO-CHASSIS-MIB OLD-CISCO-FLASH-MIB OLD-CISCO-INTERFACES-MIB OLD-CISCO-IP-MIB OLD-CISCO-SYS-MIB OLD-CISCO-TCP-MIB OLD-CISCO-TS-MIB OSPF-MIB (RFC 1253) PIM-MIB RFC1213-MIB RFC1253-MIB RMON-MIB RMON2-MIB SNMP-FRAMEWORK-MIB SNMP-MPD-MIB SNMP-NOTIFICATION-MIB SNMP-TARGET-MIB SNMPv2-MIB TCP-MIB UDP-MIB |
| Standards |
IEEE 802.1s IEEE 802.1w IEEE 802.1x IEEE 802.3ad IEEE 802.3af IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T portsIEEE 802.1D Spanning Tree Protocol IEEE 802.1p CoS Prioritization IEEE 802.1Q VLAN IEEE 802.3 10BASE-T specification IEEE 802.3u 100BASE-TX specification IEEE 802.3ab 1000BASE-T specification IEEE 802.3z 1000BASE-X specification 1000BASE-X (SFP) 1000BASE-SX 1000BASE-LX/LH 1000BASE-ZX 1000BASE-CWDM SFP 1470 nm 1000BASE-CWDM SFP 1490 nm 1000BASE-CWDM SFP 1510 nm 1000BASE-CWDM SFP 1530 nm 1000BASE-CWDM SFP 1550 nm 1000BASE-CWDM SFP 1570 nm 1000BASE-CWDM SFP 1590 nm 1000BASE-CWDM SFP 1610 nm RMON I and II standards SNMPv1, SNMPv2c, and SNMPv3 |
| Safety Certifications |
UL 60950-1, First Edition CUL to CAN/CSA 22.2 No. 60950-1, First Edition TUV/GS to EN 60950-1, First Edition CB to IEC 60950-1 with all country deviations NOM (through partners and distributors) CE Marking |
Electromagnetic Emissions Certifications |
FCC Part 15 Class A EN 55022 Class A (CISPR22) EN 55024 (CISPR24) AS/NZS CISPR22 Class A CE KCC GOST China EMC Certifications |
| Telco |
Common Language Equipment Identifier (CLEI) code |
| Warranty |
Limited Lifetime Warranty |